Casio DT-X8 Series Manual do Utilizador Página 1

System Library Manual (Version 1.10) CASIO Computer Co., Ltd. Copyright ©2011. All rights reserved. November 2011

10 Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysDisplayOff Turns off the power virtually on the terminal

100 3.73 SysSet180Rotate This function flips the display screen 180 degree. In the Device Emulator, the function does not perform, but stores the pr

101 3.74 SysGet180Rotate This function retrieves the status of display screen flipped. Calling Sequences [C++] DWORD SysGet180Rotate( ) [Visual Basi

102 3.75 SysSetBLBattery This function sets up a brightness of the backlight while the operation power is provided by the installed battery pack. In

103 3.76 SysGetBLBattery This function retrieves the brightness value of the backlight effect while the operation power is provided by the installed

104 3.77 SysSetBLExpower This function sets up a brightness of the backlight effect while the operation power is provided by the dedicated AC Adaptor

105 3.78 SysGetBLExpower This function retrieves the brightness value of the backlight effect while the operation power is provided by the dedicated

106 3.79 SysGetBLMaximum This function retrieves the maximum brightness values of the backlight for the operation powers provided by both the install

107 3.80 SysSetBLOffTime This function sets up a time period for continuously pressing the Power key until when the backlight is turned off. Callin

108 3.81 SysGetBLOffTime This function retrieves the time period set for continuously pressing the Power key until when the backlight is turned off.

109 3.82 SysPlayVibrator This function turns on the vibrator. Calling Sequences [C++] DWORD SysPlayVibrator( DWORD dwType, DWORD dwCount, DWORD dw

11 Table 3.3 LED functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysSetLED Sets up "Enable"

110 dwCount This parameter is for specifying the number of times in the range of 1 to 20 (effect only for the user defined mode) to turn on the vibra

111 3.83 SysStopVibrator This function stops turning on the vibrator. Calling Sequences [C++] DWORD SysStopVibrator( ) [Visual Basic] Public Shared

112 3.84 SysSetVibratorMute This function sets up all the vibration modes and individual mute for the vibrator. Calling Sequences [C++] DWORD SysSetV

113 3.85 SysGetVibratorMute This function retrieves all the vibration modes and individual mute for the vibrator. Calling Sequences [C++] DWORD SysGe

114 3.86 SysSetFnKeyLock This function sets up "Enable" or "Disable" for the Fn key to operate. In the Device Emulator, the func

115 3.87 SysGetFnKeyLock This function retrieves the status of "Enable" or "Disable" for the Fn key to operate. Calling Sequences

116 3.88 SysSetOneKeyLock This function sets up "Enable" or "Disable" for lock (not allow any key to be input) on each key except

117 3.89 SysGetOneKeyLock This function retrieves the status of "Enable" or "Disable" for individual key lock of all the keys exc

118 3.90 SysSetAllKeyLock This function sets up "Enable" or "Disable" for lock on all the keys except the Trigger keys, Multi key

119 3.91 SysGetAllKeyLock This function retrieves the status of "Enable" or "Disable" for key lock on all the keys. Calling Seque

12 Table 3.5 Buzzer functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysPlayBuzzer Sounds the buzzer.

120 3.92 SysSetInputMode This function sets up a key input change mode. In the Device Emulator, the function does not perform, but stores the preset

121 3.93 SysGetInputMode This function retrieves the key input change mode. Calling Sequences [C++] DWORD SysGetInputMode( ) [Visual Basic] Public S

122 3.94 SysSetNormalUserDefineKey This function sets up key codes for ordinary key input mode. In the Device Emulator, the function does not perfor

123KEYID_ENTER Enter key Y Y Y Y Y Y YYYYKEYID_0 0 key Y Y Y Y Y Y YYYYKEYID_1 1 key Y Y Y Y Y Y YYYYKEYID_2 2 key Y Y Y Y Y Y YYYYKEYID_3

124Return Values TRUE : Normal end FALSE : Internal error SYS_PARAMERR : Parameter error FUNCTION_UNSUPPORT : Unsupported error

125 Note: Virtual Key Code and Option Flag Specify any combination of the following values except for the combination of VF_PAGE and VF_NO_FIX_PAGE.

126 VF_MENU Combines VK_MENU and virtual key code. (Press ALT key simultaneously)VK_MENU down Virtual key code down Virtual key code up VK_MENU up

127 • The following values are specified for the virtual key code and option flag of the established key. Table 3.22 Virtual key code and option

128 • About VF_PAGE VF_PAGE | VK_0, VK_1, VK_2, VK_3, VF_KANA | WCH_A, VF_KANA | WCH_I, VF_KANA | WCH_U, VF_KANA | WCH_E, VK_A, VK_B, VK_C, VK_D, VK

129 Key Codes (For DT-X7 series and DT-X30 Windows CE series): Table 3.23 Name Font Code INVERT_EXCLAMATION ¡ 0x003A CENT ¢ 0x003B POUND £ 0x003C CUR

13 Table 3.7 Display functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysSet180Rotate Sets up flip ang

130 TILDE_A Ã 0x00C3 DIAERESIS_A Ä 0x00C4 RING_AVOBE_A Å 0x00C5 AE Æ 0x00C6 CEDILLA_C Ç 0x00C7 GRAVE_E È 0x00C8 ACUTE_E É 0x00C9 CIRCUMFLEX_E Ê 0x00C

131 ACUTE_E_SMALL é 0x00E9 CIRCUMFLEX_E_SMALL ê 0x00EA DIAERESIS_E_SMALL ë 0x00EB GRAVE_I_SMALL ì 0x00EC ACUTE_I_SMALL í 0x00ED CIRCUMFLEX_I_SMALL î

132 CARON_C_SMALL č 0x08AE CARON_D Ď 0x08AF CARON_D_SMALL ď 0x08B0 STROKE_D Đ 0x08B1 STROKE_D_SMALL đ 0x08B2 MACRON_E Ē 0x08B3 MACRON_E_SMALL

133 LIGATURE_IJ_SMALL ij 0x08D3 CIRCUMFLEX_J Ĵ 0x08D4 CIRCUMFLEX_J_SMALL ĵ 0x08D5 CEDILLA_K Ķ 0x08D6 CEDILLA_K_SMALL ķ 0x08D7 KRA_SMALL ĸ 0x08D8

134 CARON_R_SMALL ř 0x08F9 ACUTE_S Ś 0x08FA ACUTE_S_SMALL ś 0x08FB CIRCUMFLEX_S Ŝ 0x08FC CIRCUMFLEX_S_SMALL ŝ 0x08FD CEDILLA_S Ş 0x089F CEDILLA

135 CARON_Z Ž 0x1096 CARON_Z_SMALL ž 0x1097 LONG_S ſ 0x1098 HOOK_F ƒ 0x1099 RING_AVOBE_ACUTE_A Ǻ 0x10C1 RING_AVOBE_ACUTE_A_SMALL ǻ 0x10C2 ACUTE_AE

136 3.95 SysGetNormalUserDefineKey This function retrieves key codes for ordinary key input mode. Calling Sequences [C++] DWORD SysGetNormalUserDefin

137 3.96 SysSetUserDefineKey This function sets up user defined keys which are freely issued in either numeric, hiragana (Japanese fonts set), kataka

138 UserDefineKeyBuff[16] This parameter is for specifying key code. See SysSetNormalUserDefineKey function for the virtual key codes and option flag

139 3.97 SysGetUserDefineKey This function retrieves user defined keys which are freely issued in either numeric, hiragana (Japanese fonts set), kata

14 Table 3.9 Keys functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysSetFnKeyLock Sets up "Enabl

140 Return Values TRUE : Normal end. FALSE : Internal error. SYS_PARAMERR : Parameter error. FUNCTION_UNSUPPORT : Unsupported error.

141 3.98 SysSetFnUserDefineKey This function sets up key code for the Fn key input mode. Calling Sequences [C++] DWORD SysSetFnUserDefineKey( DWORD

142 KEYID_UP : Up key KEYID_DOWN : Down key KEYID_F1 : F1 key KEYID_F2 : F2 key KEYID_F3 : F3 key KEYID_F4 : F4 key KEYID_F5 : F5 key KEYID_F6 : F6 k

143 3.99 SysGetFnUserDefineKey This function retrieves key codes for the Fn key input mode. Calling Sequences [C++] DWORD SysGetFnUserDefineKey( DWO

144 3.100 SysSetOtherUserDefineKey This function sets up key codes for alphanumeric modes. Calling Sequences [C++] DWORD SysSetOtherUserDefineKey( W

145 pdwCode[20] This parameter is for specifying key codes (max. 20 key codes) that correspond to the modes and the key IDs. The setting must start

146 3.101 SysGetOtherUserDefineKey This function retrieves key codes for alphanumeric modes. Calling Sequences [C++] DWORD SysGetOtherUserDefineKey(

147 3.102 SysSetKeyRepeat This function sets up key codes that perform key repeat. Calling Sequences [C++] DWORD SysSetKeyRepeat( DWORD *pdwKeyRepea

148 12 No setting 0x00 13 No setting 0x00 14 No setting 0x00 15 No setting 0x00 Return Values TRUE : Normal end FUNCTION_UNSUPPORT : Unsupported

149 3.103 SysGetKeyRepeat This function retrieves key codes that perform key repeat. Calling Sequences [C++] DWORD SysGetKeyRepeat( DWORD *pdwKeyRep

15 SysSetFakeRepeat Sets up key codes of the keys that perform fake key repeat. - - - - - - - - -SysGetFakeRepeat Retrieves key codes of the keys t

150 3.104 SysSetFakeRepeat This function sets up key codes that perform faked key repeat. Faked key repeat is used to prevent the KEY_DOWN event that

151 3.105 SysGetFakeRepeat This function retrieves key codes that perform faked key repeat. Calling Sequences [C++] DWORD SysGetFakeRepeat( DWORD *p

152 3.106 SysSetAllKeyRepeat This function sets up "Enable" or "Disable" for all individual keys for key repeat set with SysSetKe

153 3.107 SysGetAllKeyRepeat This function retrieves the status of "Enable" or "Disable" for all individual keys for key repeat s

154 3.108 SysDeleteUserDefineKey This function deletes any user defined keys generated in the numeric key input mode. After the deletion, the default

155 3.109 SysDeleteUserDefineKeyEx This function deletes user defined keys that are freely issued in either numeric, hiragana (Japanese fonts set), k

156 3.110 SysGetDefaultKey This function retrieves the default keys generated in the numeric key input mode. Calling Sequences [C++] DWORD SysGetDefa

157 3.111 SysSetUserDefineKeyState This function sets up "Enable" or "Disable" for user defined keys and notifies the status to t

158 3.112 SysGetUserDefineKeyState This function retrieves the status of "Enable" or "Disable" for the user defined keys that has

159 3.113 SysSetResetUserDefineKeyState This function sets up "Disable" or "Enable" on the "Disable" for the user defin

16 Table 3.11 Event control functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysWaitForEvent Waits for

160 3.114 SysGetResetUserDefineKeyState This function retrieves the status of "Enable" or "Disable" on the "Disable" fo

161 3.115 SysSetEnableKeyMode This function sets up "Enable" or "Disable" for key mode transition when the key input mode is chan

162 3.116 SysGetEnableKeyMode This function retrieves the status of "Enable" or "Disable" for key mode transition when the key in

163 3.117 SysSetEnableTriggerKey This function sets up "Enable" or "Disable" for the Trigger keys. While the keys are set disable

164 3.118 SysGetEnableTriggerKey This function retrieves the status of "Enable" or "Disable" for input with the Trigger keys. Cal

165 3.119 SysSetFnKeyOperation This function sets up "Enable" or "Disable" for individual Fn key operations. In the Device Emula

166 3.120 SysGetFnKeyOperation This function retrieves the status in a sum of the values for individual Fn key operations that have been set to "

167 3.121 SysConvertGestureMessage This function retrieves the status of multi touch gesture by analyzing WM_GESTURE message which is issued by OS. W

168 pwParam Specify address of WPARAM variable which is related with OS issued message. If touch panel driver recognized as multi touch gesture opera

169 3.122 SysWaitForEvent This function waits for an event that occurs in driver, etc. The function does not return until when an event occurs or whe

17 3.1 SysGetModelName This function retrieves information about the handheld terminal such as model no. of the terminal, the OS version and the plat

170 Return values The function returns one of the values below. FUNCTION_UNSUPPORT : Unsupported error WAIT_TIMEOUT : The timeout elapses. WAIT_OBJ

171 3.123 SysTerminateWaitEvent This function forcibly terminates the state in wait for an event to occur set with SysWaitForEvent function. The func

18 dwPlatform This parameter is for retrieving WindowsCE version. Return Values TRUE : Normal end FUNCTION_UNSUPPORT : Unsupported error

19 3.2 SysGetDeviceIDCode This function retrieves device ID written in the EEPROM. Calling Sequences [C++] DWORD SysGetDeviceIDCode( TCHAR *pdwDevID

2 Table of the Contents Editorial Record 5 Chapter 1. Overview 6 Chapter 2. Operation Environment 7 Chapter 3. Functions List 8 3.1 SysGetM

20 3.3 SysGetUserIDCode This function retrieves the user ID written in the EEPROM. Calling Sequences [C++] DWORD SysGetUserIDCode( DWORD *pwUserID )

21 3.4 SysGetSystemName This function retrieves names and/or paths for the folders and ports listed below. Each name listed below is different accord

22Parameters dwValueID This parameter is for setting IDs listed below for names of the ports and/or paths that you wish to retrieve. STORAGE_Name_Fla

23 3.5 SysSetBootup This function sets up "Enable" or "Disable" for turning on the power by a wakeup factor. While the terminal i

24BOOT_NONE Disables turning on the power with a wakeup factor. Y - - - Y Y Y Y YBOOT_PGBUTTON Turns on the power with the Program key. - - - - - -

25 3.6 SysGetBootup This function retrieves "Enable" or "Disable" status for turning on the power by a wakeup factor. Calling Seq

26 3.7 SysSetOffMaskTime This function sets up a period of time between when the power is turned on and until when the power is turned off. In the D

27 3.8 SysGetOffMaskTime This function retrieves the time period that disables turning off the power after it has been turned on. Calling Sequences [

28 3.9 SysSetStorageOffMaskTime This function sets up a period of time that disables turning off the power after use of either one of the memory stor

29 3.10 SysGetStorageOffMaskTime This function retrieves the period of time that disables turning off the power after use of either one of the memory

33.44 SysGetAudioPowerState 66 3.45 SysKeyBackLightOn 67 3.46 SysKeyBackLightOff 68 3.47 SysGetKeyBackLightState 69 3.48 SysMultiTouchOn 70 3.49

30 3.11 SysSetPowerOnKeyTime This function sets up a period of time for continuously pressing the Power key until when the power is turned on. In th

31 3.12 SysGetPowerOnKeyTime This function retrieves the period of time for continuously pressing the Power key until when the power is turned on. Ca

32 3.13 SysSetPowerOffKeyTime This function sets up a period of time for continuously pressing the Power key until when the power is turned off. In

33 3.14 SysGetPowerOffKeyTime This function retrieves the period of time for continuously pressing the Power key until when the power is turned off.

34 3.15 SysPowerOff This function turns off the power on the terminal. In the Device Emulator, the function does not perform any. Calling Sequences

35 3.16 SysDisablePowerOff This function disables turning off the power with the Power key. In case where turning off the power has been set disabled

36 3.17 SysEnablePowerOff This function permits turning off the power with the Power key. In the Device Emulator, the function does not perform, but

37 3.18 SysGetPowerOff This function retrieves the status of "Enable" or "Disable" for permitting turning off the power with the

38 3.19 SysDisableAPO This function disables the Auto Power OFF function. If the function is carried out, turning off the power does not automaticall

39 3.20 SysEnableAPO This function enables the Auto Power OFF possible. If the function is carried out, turning off the power automatically takes pla

43.94 SysSetNormalUserDefineKey 122 3.95 SysGetNormalUserDefineKey 136 3.96 SysSetUserDefineKey 137 3.97 SysGetUserDefineKey 139 3.98 SysSetFnUs

40 3.21 SysGetAPO This function retrieves "Enable" or "Disable" status for the Auto Power OFF (APO) function. Calling Sequences [

41 3.22 SysSoftReset This function resets the terminal. In the Device Emulator, the function does not perform. Calling Sequences [C++] DWORD SysSoft

42 3.23 SysCheckIOBOX This function retrieves the status of contact established between the terminal and cradle. The condition between the two device

43 3.24 SysCheckCharger This function retrieves the contact status between the terminal and battery charger. The condition between the two devices ca

44 3.25 SysSetBackupLife This function sets up a period of time to back up data in the RAM. Data in the RAM will be backed up for approximately 1.5

45 3.26 SysGetBackupLife This function retrieves RAM backup period. Counting the period starts when VDET1 occurs. Calling Sequences [C++] DWORD SysGe

46 3.27 SysSetWakeOn This function sets up "Enable" or "Disable" status for the WakeOn function of module. It can control the Wa

47 3.28 SysGetWakeOn This function retrieves "Enable" or "Disable" status for the WakeOn function of module. It can control the W

48 3.29 SysSetVirtualOffMode This function sets up "Enable" or "Disable" for the Virtual OFF function. The Virtual OFF function m

49 Note: Follow the steps below to set the terminal in the virtual OFF mode. 1. Set the virtual OFF mode effect with SysSetVirtualOffMode function.

5 Editorial Record Manual Version no. Date edited Page Content 1.00 October 2008 Original 40 The description about the parameters is corrected. 1

50 3.30 SysSetVirtualOffModeEx This function sets up "Enable" or "Disable" for the virtual turning off including touch panel, scr

51 Return Values TRUE : Normal end FALSE : Error FUNCTION_UNSUPPORT : Unsupported error

52 3.31 SysGetVirtualOffMode This function retrieves "Enable" or "Disable" status for the Virtual OFF function. Calling Sequenc

53 3.32 SysSetSystemManagedVirtualOffMode This function sets up "Enable" or "Disable" for the system management virtual OFF mode.

54 3.33 SysGetSystemManagedVirtualOffMode This function retrieves the status of "Enable" or "Disable" for the system management v

55 3.34 SysDisplayOff This function turns off the screen on the terminal for the virtual OFF mode. In the Device Emulator, the function does not per

56 3.35 SysDisplayOn This function turns on the screen on the terminal that is being in the virtual OFF mode. Calling Sequences [C++] DWORD SysDispla

57 11. In case VDET1 occurs while the virtual OFF mode is active, the battery remaining capacity will run down quickly causing VDET2 to occur if the

58 3.36 SysGetDisplayPowerState This function retrieves the ON/OFF status for display power. Calling Sequences [C++] DWORD SysGetDisplayPowerState( )

59 3.37 SysTouchPanelOn This function turns on the touch panel on the terminal that is being in the virtual OFF mode. In the Device Emulator, the fu

6 1. Overview The System Library provides specific expanded functions for running the system such as key control, power control, and etc. integrated

60 3.38 SysTouchPanelOff This function turns off the touch panel on the terminal for the virtual OFF mode. In the Device Emulator, the function does

61 3.39 SysGetTouchPanelState This function retrieves the ON/OFF status of the touch panel. Calling Sequences [C++] DWORD SysGetTouchPanelState( ) [

62 3.40 SysSetEmulateMouseState This function sets up "Enable" or "Disable" for the Mouse Emulator. In the Device Emulator, the

63 3.41 SysGetEmulateMouseState This function retrieves the status of "Enable" or "Disable" for the Mouse Emulator. Calling Seque

64 3.42 SysAudioOff This function turns off the audio for the virtual OFF mode. In the Device Emulator, the function does not perform, but stores th

65 3.43 SysAudioOn This function turns on the audio integrated in the terminal that is being in the virtual OFF mode. In the Device Emulator, the fu

66 3.44 SysGetAudioPowerState This function retrieves the ON/OFF status of the audio. Calling Sequences [C++] DWORD SysGetAudioPowerState( ) [Visual

67 3.45 SysKeyBackLightOn This function turns on the key backlight. In the Device Emulator, the function does not perform, but stores the preset val

68 3.46 SysKeyBackLightOff This function turns off the key backlight. In the Device Emulator, the function does not perform, but stores the preset v

69 3.47 SysGetKeyBackLightState This function retrieves the status of ON/OFF for the key backlight. Calling Sequences [C++] DWORD SysGetKeyBackLightS

7 2. Operation Environment Applicable Handheld Terminals • IT-600 series • DT-X11 series • DT-X7 series • DT-X30 series • IT-3100 series • IT-8

70 3.48 SysMultiTouchOn This function enable multi touch mode. In the Device Emulator, the function does not perform, but stores the preset value as

71 3.49 SysMultiTouchOff This function disable multi touch model. In the Device Emulator, the function does not perform, but stores the preset value

72 3.50 SysGetMultiTouchState This function retrieves the Enable / Disable status of the multi touch mode. Calling Sequences [C++] DWORD SysGetMultiT

73 3.51 SysSetLED This function turns on or off the LED. Calling Sequences [C++] DWORD SysSetLED( DWORD dwLEDMode, DWORD dwNum, DWORD dwOnTime, D

74LED_NOTIFICATION Turns on the notification LED. - - - - - - - - -LED_BOTH Turns on both the LEDs (access and notification). - - - - - - - -

75 3.52 SysGetLED This function retrieves the status of the LED (Indicator #1 or #2, model dependant) being on or off. Calling Sequences [C++] DWORD

76 3.53 SysPrepareLED This function prepares for turning on the LED. With SysSetLED function, it takes about 130 milliseconds before turning on the L

77 dwOnTime This parameter is for specifying a period of ON time in the range of 0 to 255 (in the unit of 1/16 seconds) for the LED. dwOFFTime This

78 3.54 SysUpdateLED This function turns on the LED. With SysSetLED function, it takes about 130 milliseconds before turning on the LED. This is due

79 Note: If SysUpdateLED function is carried out to turn on the LED instead of SysPrepareLED function, it may be lit in an unexpected way following t

8 3. Functions List Table 3.1 Security functions Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysGetModelName

80 3.55 SysSetLEDState This function sets up "Enable" or "Disable" for turning on the system LED (Indicator #2). In the Device E

81FUNCTION_UNSUPPORT : Unsupported error Note: If either "All is set to off" has been set, or "an attribute that is to be turned o

82 3.56 SysGetLEDState This function retrieves the status of the system LED (Indicator #2) being on or off. Calling Sequences [C++] DWORD SysGetLEDSt

83 3.57 SysDisableCardDetect This function turns off the power to the virtual card by disabling the card detect terminals and removes or inserts the

84 3.58 SysEnableCardDetect This function turns on the power to the virtual card by enabling the card detect terminals after removing or inserting th

85 3.59 SysGetCardDetect This function retrieves the card detect terminals status. Calling Sequences [C++] DWORD SysGetCardDetect( DWORD socket )

86 3.60 SysDisableWLAN This function turns off the power to the integrated WLAN module (operable only on models with WLAN module integrated). In the

87 3.61 SysEnableWLAN This function turns on the power to the integrated WLAN module (operable only on models with WLAN module integrated). In the D

88 3.62 SysGetWLAN This function retrieves the status of the power to the integrated WLAN module (operable only on models with WLAN module integrated

89 3.63 SysRenewPartition This function carries out "Dismount" → "Mount" on the partition of storage so that the system can recog

9 Continue. Function Description DT-X11 IT-600 DT-X7 DT-X30 IT-3100 IT-800 IT-300 DT-X8 IT-9000 SysEnablePowerOff Sets up "Enable" or &quo

90 3.64 SysPlayBuzzer This function turns on the integrated buzzer. Calling Sequences [C++] DWORD SysPlayBuzzer( DWORD dwType, DWORD dwHelz, DWORD

91 dwHelz This parameter is for specifying frequency of buzzer sound which is effect only when user defined sound is specified. BUZ_DEFAULT is used i

92 3.65 SysStopBuzzer This function turns off the buzzer. Calling Sequences [C++] DWORD SysStopBuzzer( ) [Visual Basic] Public Shared Function SysSt

93 3.66 SysSetBuzzerVolume This function sets up a sound volume for a specific buzzer sound type. In the Device Emulator, the function does not perf

94 3.67 SysGetBuzzerVolume This function retrieves the buzzer's sound volume. Calling Sequences [C++] DWORD SysGetBuzzerVolume( DWORD dwType )

95 3.68 SysSetBuzzerMute This function sets up sound mute for all the buzzer's sound types and a specific sound type. Calling Sequences [C++] DW

96 3.69 SysGetBuzzerMute This function retrieves all the sound volumes of buzzer sound types and individual mute for the buzzer. Calling Sequences [C

97 3.70 SysSetCPUMode This function sets up the CPU frequency control. In the Device Emulator, the function does not perform, but stores the preset

98 3.71 SysGetCPUMode This function retrieves the CPU frequency control. Calling Sequences [C++] DWORD SysGetCPUMode( DWORD *pdwMode ) [Visual Basi

99 3.72 SysSetDefaultCPUMode This function resumes the CPU speed setting to the factory-default. In the Device Emulator, the function does not perfo