Casio WK-7600 Manual do Utilizador

CTK-6200/CTK-6300/CTK-7200/CTK-7300WK-6600/WK-7600MIDI ImplementationCASIO COMPUTER CO., LTD.ContentsI MIDI Message Overview 81 Product Configuration a

2 Timbre Type Specific OperationThe sound source operation performed for a sound generator instrument receive message may depend onthe value of the Tim

Part IIChannel Message5 Receive ChannelThe channel number of the channel message received by each part is shown in the table under “1.3.2Instrument Pa

Message Format: AnH kkH vvHn: MIDI Channel Numberkk: Key Numbervv: Pressure ValueSend This message is not sent by this Instrument.Receive This message

10.1 Bank Select (00H,20H)Message Format: BnH 00H mmH (MSB)BnH 20H llH (LSB)n: MIDI Channel Numbermm: MSB Value(Note1)ll: LSB Value(Send:00H, Receive:

Send Sent when the volume of any part is changed.Receive Receipt changes the volume of the corresponding part.10.5 Pan (0AH)Message Format: BnH 0AH vv

Receive Receipt changes the value of DSP Parameter 7 [1 to 8] (7-bit parameter) assigned to the partspecified by the MIDI Channel Number. Any message r

Note1 : For information about the relationship between setting values and send/receive values, see the “35.1 Off/On SettingValue Table” in “VIII Settin

10.13 Release Time (48H)Message Format: BnH 48H vvHn: MIDI Channel Numbervv: Value (Note1)Note1 : For information about the relationship between setti

Note1 : For information about the relationship between setting values and send/receive values, see the “35.10 DrawbarPosition Setting Value Table” in

10.20 Vibrato Rate (4CH)Message Format: BnH 4CH vvHn: MIDI Channel Numbervv: Value (Note1)Note1 : For information about the relationship between setti

10.5 Pan (0AH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410.6 Expression (0BH) . . . . . . . . . . . .

Note1 : For information about the relationship between setting values and send/receive values, see the “35.10 DrawbarPosition Setting Value Table” in

10.27 Drawbar Organ 2nd Percussion(54H)(Drawbar tone selected)Note : This message is valid only when a drawbar tone is selected for the MIDI channel.M

Note1 : For information about the relationship between setting values and send/receive values, see the “35.1 Off/On SettingValue Table” in “VIII Settin

Receive Receipt changes the degree of pitch modulation.10.34 Reverb Send (5BH)Message Format: BnH 5BH vvHn: MIDI Channel Numbervv: ValueSend Sent when

10.36.2 DSP EnableMessage Format: BnH 62H 01HBnH 63H 02HBnH 06H mmHBnH 26H llHn: MIDI Channel Numbermm: Value (Note1)ll: (Send:00H, Receive:Ignored)No

Note1 : The following shows the relationship between the Drawbar Foot value and the actual foot bar.ff Foot Bar00 Ft16’01 Ft5 1/3’02 Ft8’03 Ft4’04 Ft2

Send Sent when the 2nd percussion button is operated (CTK-7200, CTK-7300, WK-7600 only).Receive Receipt changes the drawbar parameter 2nd percussion (

Note1 : For information about the relationship between setting values and send/receive values, see the “35.11 Nor-mal/Vintage Setting Value Table” in

10.37.3 Coarse TuneMessage Format: BnH 64H 02HBnH 65H 00HBnH 06H mmHBnH 26H llHn: MIDI Channel Numbermm: MSB Value(28H - 58H)ll: LSB Value(Not sent, R

11.3 All Notes Off (7BH)Message Format: BnH 7BH 00Hn: MIDI Channel NumberSend Sent when MIDI send related settings are changed.Receive Receipt releases

11.6 Mono (7EH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2911.7 Poly (7FH) . . . . . . . . . . . . . . .

12 Program ChangeMessage Format: CnH ppHn: MIDI Channel Numberpp: Program Number (Note1)Note1 : For details about the relationship b etween the progra

14 Pitch BendMessage Format: EnH llH mmHn: MIDI Channel Numberll: Value LSBmm: Value MSBSend Sent when the bender is operated.Receive Receipt changes

Part IIISystem Message15 Timing ClockMessage Format: F8HSend Sent when auto accompaniment is used.Receive This message is not received by this Instrum

19.1 Universal Real Time System Exclusive MessageMessage Format: F0H 7FH...F7H19.1.1 Master VolumeMessage Format: F0H 7FH 7FH 04H 01H llH mmH F7Hll:

Receive Receipt changes the Patch Master Coarse Tune parameter.19.1.5 Reverb TypeMessage Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 01H 00H vvH F7Hvv

19.1.9 Scale/Octave 2 Byte Real Time TuningMessage Format: F0H 7FH 7FH 08H 09H ffH ggH hhH ssH ttH ... F7Hff: Channel Byte 1 (bits 0 to 1 = channel 15

Receive Receipt performs the same operation as when the GM System On message is received.19.2 Instrument-Specific System Exclusive MessageMessage Forma

Part IVInstrument-Specific System ExclusiveMessages20 FormatThis section explains the format of the Instrument-specific System Exclusive Messages. See “

The table below shows the body format for each action of Instrument-specific system exclusive mes-sages. An actual message consists of the items indica

20.3.5 act : ActionFormat: 0aaaaaaaBThis field indicates the operation of the Instrument-specific System Exclusive Message.aaaaaaaB Action Function00H I

24 System Parameters 5624.1 System Information Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5624.2 System Exclusive Pro

SBS:Start of Bulk Dump Session This message is sent to both devices to start a session to transfera series of parameter sets using one-way protocol or

20.3.7 mem : Memory Area IDFormat: 0mmmmmmmBSpecifies the memory area that is the object of the parameter transfer. The following are defined forthis In

2-dimension array block [index1][index0]Value Meaning00jjjjjjjiiiiiiiB 0000H00lllllllkkkkkkkB 0000H00nnnnnnnmmmmmmmB index100pppppppoooooooB index03-d

Bulk Parameter Set Transfer The value of this field specifies the size of the parameter set memoryimage stored in the img field. Data length indicates th

• Data = 3 : Start HBS SessionStart session to send data using handshake protocol. If a device that receives this message acceptsthe session, it needs

Table 17 6 5 4 3 2 1 0Memory data 00: [00.7] [00.6] [00.5] [00.4] [00.3] [00.2] [00.1] [00.0]Memory data 01: [01.7] [01.6] [01.5] [01.4] [01.3] [01.2]

20.3.16 EOX : End of System Exclusive MessageFormat: 11110111B (F7H)This is the End of System Exclusive Message status byte established by the MIDI st

Session “One session” refers to a series of processes that occur for one user operation. One subsessionor multiple subsessions make up a session. The

22.2.2 Example: Data send to Instrument from external deviceData Sender Data Receiver Operation(External Device) (This Instrument)SBS(OBS) -----> S

it resends the last data sent. If the correct message does not arrive after a preset number of retries,RJC is sent and the session is terminated. The

33 DSP Type List 6433.1 Single DSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6433.2 Dual DSP . . . . . .

Data Receiver Data Sender Operation(External Device) (This Instrument)SBS(HBR) -----> Session StartRequest<----- ACK AcknowledgeHBR -----> Se

22.3.9 Example: Session Generating a Timeout ErrorData Receiver Data Sender Operation(External Device) (This Instrument)SBS(HBR) -----> Session Sta

Data Receiver Data Sender Operation(External Device) (This Instrument)SBS(HBR) -----> Session Start Request<----- ACK AcknowledgeHBR -----> S

Note : Number of retries that exceeds the retries stipulated by Handshake Max Retry explained under “24.2 SystemExclusive Protocol Parameter”.22.3.12

Data Sender Data Receiver Operation(External Device) (This Instrument)SBS(HBS) -----> Session Start Request<----- ACK AcknowledgeHBS -----> S

Note2 : The sessions can be paused by sending RJC here.55

Part VParameter ListThis section explains the parameters that actually can be transferred by the Instrument.23 Using the Parameter List• Parameter fiel

24.2 System Exclusive Protocol ParameterThese parameters are related to the System Exclusive message protocol.Parameter ID R/W Block Size Array Min-De

Parameter ID R/W Block Size Array Min-Def-Max DescriptionPs Category 0019 W 00000000 7 01 00-00-7F Specifiesthe category ID of theparameter set that c

25 Patch ParameterThe main function of patch parameters is to configure the settings of the sound source of a device.25.1 Analog Input Tune ParameterTh

34.36 Chorus Reflection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7334.37 Chorus Pan . . . . . . . . . . . . . .

25.5 Master Tune ParameterThese parameters configure the Master Tuning settings.Parameter ID R/W Block Size Array Min-Def-Max DescriptionMaster Fine Tu

Parameter ID R/W Block Size Array Min-Def-Max DescriptionPosition 001E R/W 3-0:Select Bar 4 01 00-00-08 0-8Percussion 001F R/W 00000000 2 01 00-00-03

Parameter ID R/W Block Size Array Min-Def-Max DescriptionName 0000 R/W 00000000 7 10 00-20-7F Ascii CharacterRev Send 0001 R/W ↑ 7 01 00-28-7F 0 - 127

Part VIParameter Set ListThis section explains actually how parameter sets can be transferred by the Instrument with bulk dump.32 Parameter Set TableF

Part VIIDSP Parameter List33 DSP Type ListThis is a list of DSP types built into the Instrument.33.1 Single DSPNumb er ID Type01 01H Wah02 02H Compres

33.2 Dual DSPNumb er ID Type15 41H Wah-Comp16 42H Wah-Dist17 43H Wah-Cho18 44H Wah-Flan19 45H Wah-Ref20 46H Wah-Trem21 47H Wah-Pan22 48H Comp-Wah23 49

Note1 : For information about the relationship between setting values and send/receive values, see “35.17 LFO Wave Form1Setting Value Table” in “VIII

Note1 : For information about the relationship between setting values and send/receive values, see “35.18 LFO Wave Form2Setting Value Table” in “VIII

Note1 : For information about the relationship between setting values and send/receive values, see “35.21 Reflection SettingValue Table” in “VIII Setti

Note3 : For information about the relationship between setting values and send/receive values, see “35.13 0-5 Setting ValueTable” in “VIII Setting Val

IX MIDI Implementation Notation 8236 Value Notation 8236.1 Hexadecimal Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parameter Number Parameter Name Value NotesParameter7[1] WahWvform 00 - 7F Note1Parameter7[2] Wah Rate 00 - 7FParameter7[3] Wah Depth 00 - 7FParameter

Note2 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3Setting Value Table” in “VIII

34.27 Compressor TremoloParameter Number Parameter Name Value NotesParameter7[1] CmpThresh 00 - 7FParameter7[2] Cmp Level 00 - 7FParameter7[3] TrmWvfo

Note1 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3Setting Value Table” in “VIII

Note1 : For information about the relationship between setting values and send/receive values, see “35.19 LFO Wave Form3Setting Value Table” in “VIII

34.41 Reflection ChorusParameter Number Parameter Name Value NotesParameter7[1] Ref Fbk 00 - 7FParameter7[2] ChoWvform 00 - 7F Note1Parameter7[3] Cho R

34.45 Tremolo FlangerParameter Number Parameter Name Value NotesParameter7[1] TrmWvform 00 - 7F Note1Parameter7[2] Trm Rate 00 - 7FParameter7[3] Trm D

Part VIIISetting Values and Send/ Receive Values35 Setting Value Tables35.1 Off/On Setting Value TableTransmit Value Receive Value Parameter00H 00H - 3

Transmit Value Receive Value Parameter(LSB, MSB)(43H, 00H) (00H, 00H) - (5FH, 00H) 415.5 Hz(65H, 00H) (60H, 00H) - (7FH, 00H) 415.6 Hz(07H, 01H) (00H,

Transmit Value Receive Value Parameter- 00H - 07H 0(shortest)- 08H - 0FH 1- 10H - 17H 2- 18H - 1FH 3- 20H - 27H 4- 28H - 2FH 5- 30H - 37H 6- 38H - 3FH

Part IMIDI Message Overview1 Product Configuration as a MIDI DeviceAs a MIDI device, this Instrument consists of the System Section, Sound Generator Se

35.13 0-5 Setting Value TableTransmit Value Receive Value Parameter00H 00H - 14H 019H 15H - 29H 133H 2AH - 3FH 24CH 40H - 54H 366H 55H - 69H 47FH 6AH

35.20 LoFi Noise Level Setting Value TableTransmit Value Receive Value Parameter00H 00H - 14H 019H 15H - 29H 133H 2AH - 3FH 24CH 40H - 54H 366H 55H -

Part IXMIDI Implementation Notation36 Value Notation36.1 Hexadecimal NotationMIDI implementation sometimes requires that data be expressed in hexadeci

Decimal Hexadecimal Binary0 00H 00000000B1 01H 00000001B2 02H 00000010B3 03H 00000011B4 04H 00000100B5 05H 00000101B6 06H 00000110B7 07H 00000111B8 08

1.3.2 Instrument Part BlockThe instrument part section consists of a total of 32 instrument parts, divided into two groups, namedGroup A and Group B o